HC_APTBS — Herlic Test Bench Dashboard Bench Pump Tests Results Settings Bench readings Connections CAN bus Bench controller Pump ECU K-Line session ONLINE OFFLINE OPEN CLOSED FAILED Active alarms System OK — no active alarms Test summary Active: Phase: No test is currently running. Last test: PASS Last test: FAIL Start Test Requires a selected pump and an open CAN connection. Connect & Auto Test Opens K-Line, reads the pump, unlocks if required, turns on the bench and starts the test in one step. Stop EMERGENCY STOP Bench RPM Q delivery Pressure P1 Pressure P2 Oil in T Oil out T rpm cc/s bar °C Elapsed: Pump: No pump Devices CAN K-Line Bench Refresh Available Connected Session active Error No devices found Bench controller Connecting to CAN… Disconnecting CAN… CAN connected CAN disconnected Operation failed Confirm device change The {0} session is active. Disconnect? A test is running. Changing device state may abort it. Continue? Status: CAN Bench Pump K-Line Connected Connection failed Disconnected Connect CAN Disconnect CAN rpm Target: V: T. In: T. Out: T. 4: T. Tank: P1: P2: Q-Del.: Q-Over: cc/stroke P-RPM: P-Temp: P-ME: P-FBkW: PSG Encoder: Direction LEFT RIGHT Bench Motor START STOP Set RPM: GO Oil Pump OIL OFF OIL ON Counter Turns: Send Relays Electronic Deposit Cooler Deposit Heater T-in Cooler Flasher 4-Pulse Signal ON OFF Temperature Setpoint Tolerance Apply setpoint Identification Fault Codes Live Data Adaptation Immobilizer Unlock K-Line session is not open. Identify a pump to begin diagnostics. Select a pump on the Identification tab to enable diagnostics. No immobilizer unlock is currently in progress for this pump. Engineering values (raw) Read DTCs Clear DTCs No fault codes reported by the ECU. Last read: Fault codes cleared. Authentication required This section can modify pump parameters. Sign in to unlock. Authenticate… Unlocked as Lock T-hyb RPM T-ein 1/min °C µs Pump Commands ME FBKW Pre-inj Live Data Pump RPM T-hyb T-ein ME FBKW RPM trend Active BIP-STATUS BIP: BIP captured, no current fault No BIP within entire detection window No BIP in detection window, MV off (o.k.) No MV drive due to MAB BIP captured, but deviation from characteristic curve too large BIP captured, but too close to HLU switching point No BIP within entire detection window (Ford) Idling Calibration Version Current DFI Fault Codes Identification Brand No pump selected CAN K-Line No pump selected — select a pump to enable diagnostics. Fast unlock attempt... Pump: DFI: Pump ID: Serial No: Model Ref: Data Record: Pump Ctrl: Model Index: SW Ver 1: SW Ver 2: Errors: Error: Read K-Line Disconnect No K-Line device found READ WRITE DFI: AUTO FBKW - Advance Control ME - Quantity Control ME - Pre-inj Quantity Min / Step / Max Min Step Max CAN-Bus ID (0x) Byte L Byte H Filter α Enable formula ADVANCE MONITORING PSG: INJ: ABS °: LOCK °: Set PSG zero reference Set INJ zero reference RPM Command Actual Target Apply Actuators & Relays Direction Right Left Oil Pump Counter Set Temperature Setpoint °C Tolerance ±°C Heater Dep. Cool. T-In Cool. Misc Relays Electronic Flasher Pulse 4 Live Data Live Charts Advance Monitor Lock Offset Δ° Zero PSG Zero INJ Lock Bench RPM Pressure P1 Pressure P2 Q Delivery Q Over T-In T-Out T4 T-Tank Bench Temp bar cc/s Q Delivery Q Over Pressure P1 Pressure P2 ▶ START TEST ■ STOP 📄 Report Show values Check All s remaining Cond: Meas: M/s: Required: Test: Critical Plan — select phases to run estimated All phases Hover a phase for required / send values Cond Meas M/s no measurements Test started... Test stopped. Ready to start Not ready Running Select at least one phase to start. Preconditions Pump selected CAN bus live K-Line session open Bench RPM at zero Oil pump running No critical alarms User authenticated Fix All preconditions met. Ready to start. Resolve the items above before starting. This test requires operator authentication. Authenticate… Go to Pump page to select a pump. Open the Dashboard to check CAN connection. Open a K-Line session on the Pump page. Stop the bench from the Bench page. Start the oil pump from the Bench page. Clear critical alarms on the Dashboard. Authenticate the operator above. ■ Abort Pause Resume Retry phase Skip phase Coming soon PASSED FAILED View full results Run again Clear test data Abort test? Stopping the test now will end the current phase and return partial results. Continue? Abort Keep running Warm-up Adjustment Flow Servo valve Upstroke Pre-injection Phase Parameter Target Tol ± Average Result All Tests Results Test history (session) Run detail Observations / Notes Export PDF… No completed tests yet. Finish a test on the Tests page to see it here. Select a run on the left to view its details. INTERRUPTED Remove this entry Clear session Clear all history entries for this session? PASS FAIL Accept Cancel Close Save OK Yes No WARNING disabled Dismiss Generate Report Client List Client Data Company Data Name: Client information Observations Operator: Company: Company information Delete Client Generate User Authentication Username: Password: Power Supply Warning VOLTAGE: The selected pump requires power supply. SWITCH THE POWER SUPPLY TO Oil Pump Activation You are about to activate the oil pump. Confirm that the oil level is adequate and all connections are secure before proceeding. I have checked — no leaks, connections are ready RPM Safety Warning The oil pump is OFF. Running the bench motor without oil circulation can cause bearing damage to the pump. Turn on oil pump and start the bench I know what I'm doing — start without oil Immobilizer Unlock PROGRESS Phase 1: Sending unlock signals Phase 2: Testing Phase 2: Sending... CANCELLED UNLOCKED UNLOCK FAILED Type {0} Retry unlock K-Line Fault Codes Fault codes: Read Clear Settings General Safety PID Motor Report K-Line Advanced Language: Days to keep logs: Max. temperature (°C): Min. temperature (°C): Safety RPM limit: Max. pressure (bar): UP tolerance extension: PFP tolerance extension: Ignore T-in by default Skip oil-pump confirmation during Auto Test (operator accepts leak-check responsibility up front) Proportional (P): Integral (I): Derivative (D): Loop period (ms): Encoder resolution: Voltage for max RPM (V): Max RPM: Right = relay ON RPM-Voltage Table RPM Voltage (V) Add Remove Company name: Company information: Report logo path: Select Logo Image K-Line port (FTDI): Refresh Select an FTDI device or type the serial number manually. Bench interface (ms): While reading K-Line (ms): CAN bus read (ms): Pump request (ms): Pump params (ms): Blink interval (ms): Flasher interval (ms): RPM chart rate (Hz): Users Manage Users... User Management Username Add... Remove Change Password... Close Add User Change password for '{0}' Remove User Remove user '{0}'? Invalid Input Username and password cannot be empty. Invalid Input Username must not contain ':' or ','. Duplicate User A user with that name already exists. Cannot Remove Cannot remove the last remaining user. Auto Test Running pre-flight checks… Connecting K-Line… Reading pump identification… Unlocking pump… Unlocking pump — {0} Turning on bench… Starting oil pump… Starting test procedure… Test running… Test running — {0} Auto Test completed. Aborted — {0} Cancelled by operator Pre-flight conditions not met Failed to open K-Line session K-Line session lost Failed to read pump identification Pump ID not recognised Immobilizer unlock failed Bench CAN bus lost Pump ECU CAN lost Critical alarm triggered Oil-pump confirmation cancelled by operator Test interrupted Test failed Unexpected error Failed to generate report:\n{0} Report Error PSG sync pulse not detected. Check encoder connection. PSG Error EMERGENCY STOP: {0} K-Line device not found. Check that the FTDI adapter is connected. K-Line Error Invalid username or password.\n(Both are case-sensitive.) Authentication Error VP44 INJECTION PUMP TEST REPORT Generated by HC-APTBS Page of Date: {0:dd/MM/yyyy HH:mm} Operator: {0} Client: {0} PUMP IDENTIFICATION Pump ID: Model: Serial No.: Injector: Tube: Valve: Tension: Rotation: Lock Angle: Measured: Chaveta: Pre-Inj.: ECU DATA (K-Line) OVERALL TEST RESULT Tests executed: {0} of {1} Parameters evaluated: {0} / {1} passed TEST: {0} Phase Parameter Target Tolerance ± Average Result ⚠ Error bits: {0} No sample data available for graphical display. Samples: {0} | Target: {1} ± {2} | Average: {3} | Result: {4} OBSERVATIONS